Which CPU thermal paste is good for 2017?

A CPU thermal paste is an important element in any cooling system imposed on the central processing unite. It works like a medium between the upper surface of the CPU and the lower surface of the heat-sink in order to provide an optimal heat conductivity between the two surfaces, thus to properly dissipate the excessive temperature caused by the heavy workload processing inside the CPU.

If you really feel like you need to “do” something, feel free to use a razor blade or credit card to spread the paste over the processor a bit. The result was a CPU that with the stock cooler was easy to OC about 300 mhz above stock (3.8ghz to 4.1 Ghz) speed and still be within safe operating tolerances. Recently, the good cpu thermal paste for 2017 must take care of handling every temperature degree that the CPU emits. Another very common mistake is the placement of warranty seals on the contact part between the heatsink and the processor. But one needs to take care of properly removing and reinstalling the CPU because these pins can be bent if handled roughly. In many ways, these combine the benefits of thermal pads and greases or gels – they’re easy to apply and have good thermal conductivity and spread, but are less susceptible to leakage or hardening.

thermal paste syringe

How important is a CPU thermal paste is

Recipes usually call for only the finest ingredients, and the very same principle is true for overclocker and hardware enthusiast products. Spread a thin layer of the grease all over the surface that will be covered by the LED board. It gives better conduction between the heatsink and CPU/GPU because it fills in all those little imperfections on the heatsink that cause poor conduction due to having air in them. If everything is secure and sitting flush, connect the cooler’s fan connector to the CPU fan header on the motherboard. Be sure to align the fan so that the air travels from inside the case to outside.

Combining twin 140mm fans running at up to 2000RPM, an ultra-efficient 26mm-thick radiator, and the ultimate in customized controls, the H115i provides extreme cooling capability along with an excellent acoustic profile. It could also be a problem with your CPU cooler itself. The hard drive cage is often a good candidate for this. Arctic Silver‘s illustrated instructions, while somewhat overwrought, are illustrated and pretty easy to follow. Quite the contrary, the cost impact of a few extra degrees over several years of running a computer is likely a ton more than whatever amount of 6-10$ paste you might use.

The compositions of a good thermal paste

Don’t accept a processor with seals covering it. Under any circumstances, avoid touching the contacts on the processor socket and at all cost DO NOT touch the pins on the motherboard socket. In the future, nanotechnology may also help out. Thermal pastes are often times mixed from at least a dozen different components, while heatsink coolers may use only one or two different metals. In the pictures we are using a large LED board so we have a large area to cover.

You only need as much thermal paste as it takes to fill in these little holes/divots. Arrows on the fan’s sides indicate direction of air movement. Despite costing just a few dollars more than the H110i v2, the H115i is significantly better. In this case, you would need to purchase a new CPU cooler, remove the old cooler, clean the old paste off of the CPU, apply new thermal paste, and then attach the new cooler. Once you’ve figured out where all the parts go, decide how you’re going to run your tubing.

applying thermal paste

Thermal connectivity level

You may need to mix the components first, but after that the application should be about the same as thermal paste. In fact, the added burden on your CPU from the heat (and even running extra voltage) affects performance down the line, which is why I rarely overclock. If you have a processor with a seal on its top, remove it right away. The images above indicate the right and the wrong ways to hold the CPU cooler during its removal or installation. Researchers at Purdue University in Indiana have already created a TIM based on carbon nanotubes, which create a Velcro-like mesh of fibres between two surfaces.

Beside a good thermal paste, you have to pick a high-quality cpu cooler in order to ensure the best level of performance for the overall system. Armed with the knowledge above, you might expect any silver-based product to be a clear-cut winner. But building a superior product by design is different than what you receive in execution. Once you have a coating of grease over the surface, place your LEDs on, pressing lightly, and let sit. Some people will lap thier heatasink to get a smoother finish. Screw the retention ring into the bottom brace, through the heat sink mounting holes surrounding the CPU socket. So what’s the catch?

Conclusion

Finally, it could also be a problem with the airflow in your computer case. From the pump, you can go to your radiator, then your waterblock, then back to the reservoir. Do consult whatever instructions came with the stuff. The heat also impacts your motherboard, which in turn also impacts your other parts like RAM, and even the extra case heat can impact things like the video card or hard disks. The processor in Figure 43 is a poor 200 MHz Pentium MMX.